In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell

Mie Møller Storm, Rune E. Johnsen, Reza Younesi, Poul Norby

Research output: Contribution to conferencePosterResearchpeer-review

Abstract

In situ studies give an opportunity to explore systems with a minimum of external interference. As Li-air batteries hold the promise for a future battery technology the investigation of the discharge and charge components of the cathode and anode is of importance, as these components may hold the key to making a large capacity rechargeable battery[1]. Different design for in situ XRD studies of Li-O2 batteries has been published, based on coin cell like configuration[2] [3] or Swagelok designs [4]. Capillary batteries have been investigated for the Li-ion system since its development[5], but no capillary batteries of Li-air has yet been designed. Some of the advantage of the capillary battery design lies in its ability to separate the cathode and anode and avoid the use of glass fiber or separators, which may enable ex situ analysis of battery components. The battery design consist of a electrolyte filled capillary with anode and cathode in each end suspended on stainless steel wires, the oxygen in-let is placed on the cathode side of the capillary with a flushing system for oxygen in-let. In this study we present a flexible design of a capillary based Li-O2 battery with discharge and charge investigated in dimethxyethane (DME) with synchrotron XRD. The in situ study in these batteries show clearly how Li2O2 precipitates on the cathode side of the battery during discharge (see Figure), as the Li2O2 reflections at 21.2°, 22.5° and 37.1° grows. The reflection at 27.8, 28.4 and 32.16 is from a stainless steel wire where the cathode is attached. The in situ XRD measurements show how the Li2O2 growth depend on current discharge rate and how the FWHM changes dependent on reflection and charge/discharge.Several cells were tested both ex situ and in situ, and in situ XRD for 1st discharge/charge and 2nd discharge/charge of the battery cell were measured, to give a better understanding of the electrochemistry in the Li-O2battery. 1. Girishkumar, G., et al.. The Journal of Physical Chemistry Letters, 2010. 1(14): p. 2193-2203. 2. Lim, H., E. Yilmaz, and H.R. Byon, The Journal of Physical Chemistry Letters, 2012. 3(21): p. 3210-3215. 3. Ryan, K.R., et al.,. Journal of Materials Chemistry A, 2013. 1(23): p. 6915-6919. 4. Shui, J.-L., et al., Nat Commun, 2013. 4. 5. Johnsen, R.E. and P. Norby,. Journal of Applied Crystallography, 2013. 46(6): p. 1537-1543. [Formula]
Original languageEnglish
Publication date2014
Number of pages1
Publication statusPublished - 2014
Event17th International Meeting on Lithium Batteries - Como, Italy
Duration: 10 Jun 201414 Jun 2014
Conference number: 17

Conference

Conference17th International Meeting on Lithium Batteries
Number17
CountryItaly
CityComo
Period10/06/201414/06/2014

Cite this

Storm, M. M., Johnsen, R. E., Younesi, R., & Norby, P. (2014). In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell. Poster session presented at 17th International Meeting on Lithium Batteries, Como, Italy.
Storm, Mie Møller ; Johnsen, Rune E. ; Younesi, Reza ; Norby, Poul. / In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell. Poster session presented at 17th International Meeting on Lithium Batteries, Como, Italy.1 p.
@conference{5320484332344a87af91dda0eed09fea,
title = "In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell",
abstract = "In situ studies give an opportunity to explore systems with a minimum of external interference. As Li-air batteries hold the promise for a future battery technology the investigation of the discharge and charge components of the cathode and anode is of importance, as these components may hold the key to making a large capacity rechargeable battery[1]. Different design for in situ XRD studies of Li-O2 batteries has been published, based on coin cell like configuration[2] [3] or Swagelok designs [4]. Capillary batteries have been investigated for the Li-ion system since its development[5], but no capillary batteries of Li-air has yet been designed. Some of the advantage of the capillary battery design lies in its ability to separate the cathode and anode and avoid the use of glass fiber or separators, which may enable ex situ analysis of battery components. The battery design consist of a electrolyte filled capillary with anode and cathode in each end suspended on stainless steel wires, the oxygen in-let is placed on the cathode side of the capillary with a flushing system for oxygen in-let. In this study we present a flexible design of a capillary based Li-O2 battery with discharge and charge investigated in dimethxyethane (DME) with synchrotron XRD. The in situ study in these batteries show clearly how Li2O2 precipitates on the cathode side of the battery during discharge (see Figure), as the Li2O2 reflections at 21.2°, 22.5° and 37.1° grows. The reflection at 27.8, 28.4 and 32.16 is from a stainless steel wire where the cathode is attached. The in situ XRD measurements show how the Li2O2 growth depend on current discharge rate and how the FWHM changes dependent on reflection and charge/discharge.Several cells were tested both ex situ and in situ, and in situ XRD for 1st discharge/charge and 2nd discharge/charge of the battery cell were measured, to give a better understanding of the electrochemistry in the Li-O2battery. 1. Girishkumar, G., et al.. The Journal of Physical Chemistry Letters, 2010. 1(14): p. 2193-2203. 2. Lim, H., E. Yilmaz, and H.R. Byon, The Journal of Physical Chemistry Letters, 2012. 3(21): p. 3210-3215. 3. Ryan, K.R., et al.,. Journal of Materials Chemistry A, 2013. 1(23): p. 6915-6919. 4. Shui, J.-L., et al., Nat Commun, 2013. 4. 5. Johnsen, R.E. and P. Norby,. Journal of Applied Crystallography, 2013. 46(6): p. 1537-1543. [Formula]",
author = "Storm, {Mie M{\o}ller} and Johnsen, {Rune E.} and Reza Younesi and Poul Norby",
year = "2014",
language = "English",
note = "17th International Meeting on Lithium Batteries ; Conference date: 10-06-2014 Through 14-06-2014",

}

Storm, MM, Johnsen, RE, Younesi, R & Norby, P 2014, 'In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell' 17th International Meeting on Lithium Batteries, Como, Italy, 10/06/2014 - 14/06/2014, .

In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell. / Storm, Mie Møller; Johnsen, Rune E.; Younesi, Reza; Norby, Poul.

2014. Poster session presented at 17th International Meeting on Lithium Batteries, Como, Italy.

Research output: Contribution to conferencePosterResearchpeer-review

TY - CONF

T1 - In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell

AU - Storm, Mie Møller

AU - Johnsen, Rune E.

AU - Younesi, Reza

AU - Norby, Poul

PY - 2014

Y1 - 2014

N2 - In situ studies give an opportunity to explore systems with a minimum of external interference. As Li-air batteries hold the promise for a future battery technology the investigation of the discharge and charge components of the cathode and anode is of importance, as these components may hold the key to making a large capacity rechargeable battery[1]. Different design for in situ XRD studies of Li-O2 batteries has been published, based on coin cell like configuration[2] [3] or Swagelok designs [4]. Capillary batteries have been investigated for the Li-ion system since its development[5], but no capillary batteries of Li-air has yet been designed. Some of the advantage of the capillary battery design lies in its ability to separate the cathode and anode and avoid the use of glass fiber or separators, which may enable ex situ analysis of battery components. The battery design consist of a electrolyte filled capillary with anode and cathode in each end suspended on stainless steel wires, the oxygen in-let is placed on the cathode side of the capillary with a flushing system for oxygen in-let. In this study we present a flexible design of a capillary based Li-O2 battery with discharge and charge investigated in dimethxyethane (DME) with synchrotron XRD. The in situ study in these batteries show clearly how Li2O2 precipitates on the cathode side of the battery during discharge (see Figure), as the Li2O2 reflections at 21.2°, 22.5° and 37.1° grows. The reflection at 27.8, 28.4 and 32.16 is from a stainless steel wire where the cathode is attached. The in situ XRD measurements show how the Li2O2 growth depend on current discharge rate and how the FWHM changes dependent on reflection and charge/discharge.Several cells were tested both ex situ and in situ, and in situ XRD for 1st discharge/charge and 2nd discharge/charge of the battery cell were measured, to give a better understanding of the electrochemistry in the Li-O2battery. 1. Girishkumar, G., et al.. The Journal of Physical Chemistry Letters, 2010. 1(14): p. 2193-2203. 2. Lim, H., E. Yilmaz, and H.R. Byon, The Journal of Physical Chemistry Letters, 2012. 3(21): p. 3210-3215. 3. Ryan, K.R., et al.,. Journal of Materials Chemistry A, 2013. 1(23): p. 6915-6919. 4. Shui, J.-L., et al., Nat Commun, 2013. 4. 5. Johnsen, R.E. and P. Norby,. Journal of Applied Crystallography, 2013. 46(6): p. 1537-1543. [Formula]

AB - In situ studies give an opportunity to explore systems with a minimum of external interference. As Li-air batteries hold the promise for a future battery technology the investigation of the discharge and charge components of the cathode and anode is of importance, as these components may hold the key to making a large capacity rechargeable battery[1]. Different design for in situ XRD studies of Li-O2 batteries has been published, based on coin cell like configuration[2] [3] or Swagelok designs [4]. Capillary batteries have been investigated for the Li-ion system since its development[5], but no capillary batteries of Li-air has yet been designed. Some of the advantage of the capillary battery design lies in its ability to separate the cathode and anode and avoid the use of glass fiber or separators, which may enable ex situ analysis of battery components. The battery design consist of a electrolyte filled capillary with anode and cathode in each end suspended on stainless steel wires, the oxygen in-let is placed on the cathode side of the capillary with a flushing system for oxygen in-let. In this study we present a flexible design of a capillary based Li-O2 battery with discharge and charge investigated in dimethxyethane (DME) with synchrotron XRD. The in situ study in these batteries show clearly how Li2O2 precipitates on the cathode side of the battery during discharge (see Figure), as the Li2O2 reflections at 21.2°, 22.5° and 37.1° grows. The reflection at 27.8, 28.4 and 32.16 is from a stainless steel wire where the cathode is attached. The in situ XRD measurements show how the Li2O2 growth depend on current discharge rate and how the FWHM changes dependent on reflection and charge/discharge.Several cells were tested both ex situ and in situ, and in situ XRD for 1st discharge/charge and 2nd discharge/charge of the battery cell were measured, to give a better understanding of the electrochemistry in the Li-O2battery. 1. Girishkumar, G., et al.. The Journal of Physical Chemistry Letters, 2010. 1(14): p. 2193-2203. 2. Lim, H., E. Yilmaz, and H.R. Byon, The Journal of Physical Chemistry Letters, 2012. 3(21): p. 3210-3215. 3. Ryan, K.R., et al.,. Journal of Materials Chemistry A, 2013. 1(23): p. 6915-6919. 4. Shui, J.-L., et al., Nat Commun, 2013. 4. 5. Johnsen, R.E. and P. Norby,. Journal of Applied Crystallography, 2013. 46(6): p. 1537-1543. [Formula]

M3 - Poster

ER -

Storm MM, Johnsen RE, Younesi R, Norby P. In Situ Synchrotron XRD on a Capillary Li-O2 Battery Cell. 2014. Poster session presented at 17th International Meeting on Lithium Batteries, Como, Italy.